The RF Signal Chain

Every radio transmission follows this path. Click any stage to explore it.

MICROPHONE audio in MODULATOR encode signal TRANSMITTER amplify RF ANTENNA EM radiation PROPAGATION ionosphere/space RECEIVER decode RF Radio Frequency energy (electromagnetic wave)

Radio Frequency Spectrum β€” Interactive

Drag the slider to explore different frequency ranges and their uses. Ham bands are highlighted in green.

Frequency: 14.000 MHz   Wavelength: 21.4 m

Explore by Topic

πŸ“‹

Regulations (G1)

Band privileges, licensing, FCC rules

πŸŽ™οΈ

Operating (G2)

Phone, CW, digital, nets

🌐

Propagation (G3)

Ionosphere, solar activity, paths

πŸ“»

Equipment (G4)

Transceivers, test gear, RFI

⚑

Electronics (G5–G7)

Circuits, components, power

πŸ“‘

Signals & Modes (G8)

Modulation, digital, bandwidth

πŸ—Ό

Antennas (G9)

Dipoles, Yagi, feed lines, SWR

πŸ›‘οΈ

Safety (G0)

RF exposure, electrical safety

🌟

Programs & Services

ARES, RACES, satellites, remote

HF Band Privileges β€” General vs. Extra

General class licensees have access to most HF bands. The amber zones are Extra-only. Click a band for details.

Power Limits

HF (most bands)1,500 W PEP
60 meters (USB only)100 W ERP
Near repeater inputSee 97.313
Novice/Tech HF200 W PEP
Use the minimum power necessary to maintain contact.

Third-Party Traffic

US to USAlways OK
US to foreignNeed treaty
Paid operatorEmployer rules apply
Emergency commsNo restriction
Content restrictionNo music, profanity

Phonetic Alphabet β€” Interactive Drill

The NATO phonetic alphabet is used to spell out callsigns and words clearly over radio.

Morse Code β€” Interactive Trainer

Click the letters to hear their Morse pattern. Use the button to decode text.

Net Check-In Procedure

1Listen first β€” is the frequency in use?
2Wait for net control to open check-ins
3Give your callsign (phonetic if needed)
4Pass traffic or receive assignment

SSB Conventions

14 MHz (20m) phoneUSB (Upper)
7 MHz (40m) phoneUSB (by convention)
3.8 MHz (75m) phoneLSB or USB
Calling frequency14.225 MHz
DX window (20m)14.000–14.025 MHz

CW (Morse) Operating

Common abbreviations

QSOContact/conversation
QRMMan-made interference
QRNNatural static
QSYChange frequency
73Best regards

RST Signal Report

R = Readability (1–5)
S = Signal Strength (1–9)
T = Tone quality, CW only (1–9)
A "5 9 9" report = perfect in all three categories.

Ionospheric Layers β€” Interactive

The ionosphere has distinct layers that affect different frequency ranges. Click a layer to learn about it.

D Layer

60–90 km altitude, daytime only

E Layer

90–120 km altitude

F1 Layer

150–250 km, daytime

F2 Layer

250–400+ km, exists day & night

D Layer
Absorbs MF/lower HF signals (AM broadcast, 160m, 80m) during the day. Disappears at night, allowing those bands to skip farther. Does not reflect β€” only absorbs. This is why you hear distant AM stations better at night.
Primary roleAbsorption
ExistsDaytime only
Bands affected160m, 80m, 40m
Disappears atSunset

Solar Cycle β€” MUF Simulator

The sun drives propagation. Higher solar activity raises the Maximum Usable Frequency (MUF), opening up higher bands.

Solar Flux Index (SFI): 120   Sunspot Number: ~85

Skip Distance Simulator

When a signal bounces off the ionosphere, there's a "skip zone" where the signal cannot be heard. Adjust frequency to see how skip distance changes.

Frequency: 14 MHz

SWR Meter β€” Interactive

Standing Wave Ratio (SWR) measures how well the antenna is matched to the feed line. 1:1 is perfect; above 3:1 risks damage.

Antenna impedance: 50 Ξ©
1:12:13:15:110:1

S-Meter β€” Signal Strength

The S-meter shows received signal strength. Each S-unit = 6 dB (4Γ— power ratio). S9 is the reference at 50 Β΅V.

Signal level: S7   28 Β΅V
dB over S9: Above S9, signal is reported as "+20 dB", "+40 dB" etc. Each 6 dB = one S-unit = 4Γ— power.

Oscilloscope Basics

ShowsVoltage vs. time
TriggerStabilizes display
TimebaseX-axis (time/div)
Volts/divY-axis scale
Use forAudio, RF envelope, power

Dummy Load

A 50 Ξ© non-radiating load used for transmitter testing without sending on-air.

Impedance50 Ξ©
Must handleFull transmitter power
No antenna neededAbsorbs all RF as heat
Always use a dummy load when testing β€” not your antenna!

Ohm's Law & Power Calculator

Enter any two values to calculate the rest. E = IR, P = EI = IΒ²R = EΒ²/R

Results will appear here

dB Power & Voltage Calculator

Decibels are logarithmic. +3 dB β‰ˆ 2Γ— power. +10 dB = 10Γ— power. +20 dB = 10Γ— voltage.

dB change: +10 dB

Filter Types

Low-passPasses low freq, blocks high
High-passPasses high freq, blocks low
Band-passPasses narrow range
Band-stopRejects narrow range (notch)
Low-pass filters on transmitter output reduce harmonic interference.

Capacitors & Inductors

Capacitor (C)Stores electric field (Farads)
Inductor (L)Stores magnetic field (Henries)
XC (reactance)1 / (2Ο€fC)
XL (reactance)2Ο€fL
Resonance f1 / (2Ο€βˆšLC)

Antenna Types β€” Interactive Explorer

Half-wave Dipole
Vertical
Yagi
Loop

Dipole Length Calculator

The classic formula: Length (feet) = 468 / frequency (MHz). Adjust for wire velocity factor.

Frequency: 14.200 MHz

Coax Cable Types

RG-8 / RG-213Low loss, 50 Ξ©
RG-58Flexible, higher loss, 50 Ξ©
RG-5975 Ξ©, TV/video use
RG-174Very small, high loss
HardlineVery low loss, rigid
Coax loss increases with frequency β€” use the best cable you can afford on VHF/UHF.

Yagi Antenna

Reflector5% longer than driven
Driven elementΒ½ wave dipole
Director(s)5% shorter than driven
Gain per element~3 dB first director
Feedpoint impedance50–75 Ξ© typical

Modulation Visualizer

See how different modulation types encode audio onto an RF carrier.

AM
SSB
FM
CW
Digital

Typical Bandwidths

ModeTypical BandwidthNotes
SSB (voice)~2.4 kHzMost efficient voice mode
AM (voice)~6 kHz2Γ— bandwidth of SSB
FM (voice)~10–15 kHzVHF/UHF repeaters
CW (Morse)~150–500 HzNarrowest, best S/N ratio
PSK31~31 HzVery narrow digital
FT8~50 HzWeak signal DX
RTTY~300 Hz170 Hz shift typical
WSPR~6 HzNarrowestβ€”beacon mode

Digital Mode Guide

FT8Weak signal DX, 15s cycles
PSK31Keyboard QSO, low power
RTTYTeletype, contests
APRSPosition/data, 144.390
WinlinkEmail over radio
D-STAR / DMRDigital voice/data

Emission Designators

A3EAM double sideband
J3ESSB, suppressed carrier
A1ACW (carrier keying)
F3EFM voice
G3EPM (phase modulation)
F1BFSK data (RTTY)

RF Exposure (MPE) β€” Power/Distance Calculator

Maximum Permissible Exposure depends on frequency, power, antenna gain, and distance. Controlled environments (hams & family) have higher limits than uncontrolled (general public).

Transmit power: 100 W
Antenna gain: 0 dBi

Electrical Safety Rules

Never work on live circuits. Capacitors in power supplies can hold lethal charges even when unplugged!
Chassis groundConnect to AC safety ground
Fuse placementBoth supply leads (12V mobile)
InterlockBreaks power when covers open
Bleeder resistorDischarges capacitors safely

Tower & Antenna Safety

ClimbingAlways use a safety harness
Near power linesNEVER β€” extreme hazard
Tower heightAntenna height + Β½ tower length
Lightning protectionGround and disconnect
Guy wiresBreak every 20 feet with insulators

RF Exposure Duty Cycle Guide

ModeDuty CycleEffect on MPE
SSB Voice (avg)~20%1/5 of CW power
CW~40%40% of key-down power
FM / Digital100%Full power β€” worst case
SSTV~100%Same as FM
ATV (video)~100%Same as FM

🚨 ARES β€” Amateur Radio Emergency Service

ARRL-sponsored program providing emergency communications support.

SponsorARRL
ActivationARRL Section Manager
Served agenciesRed Cross, hospitals, EOC
TrainingICS 100/200/700/800
ARES operators are volunteers; activation is at request of served agency.

πŸ›οΈ RACES β€” Radio Amateur Civil Emergency Service

FCC Part 97 program for communications during declared civil emergencies.

Legal basisFCC Part 97.407
ActivationCivil defense authority
RestrictionGovt agencies only during emergency
FrequenciesAny amateur frequencies
During RACES operations, only specific frequencies and types of communications are allowed.

πŸ›°οΈ Satellite Operations

Amateur satellites use uplink (your signal to satellite) and downlink (satellite to you) on different bands.

Doppler shiftAdjust as satellite moves
LEO orbit period~90–100 minutes
TransponderReceives uplink, retransmits
Linear transponderSSB/CW through satellite
FM satelliteSingle uplink frequency

Common satellite bands

Uplink (Mode V/U)144 MHz up / 432 down
Uplink (Mode L/S)1.2 GHz up / 2.4 GHz down
AMSAT-NAOperates many satellites
Doppler effect: As a satellite approaches, the frequency appears higher. Tune down on downlink, up on uplink as satellite approaches β€” reverse as it recedes.

πŸ“‘ Remote and Auxiliary Operations

Remote Control (97.213)

Control linkAny reliable link (internet OK)
IdentifierMust ID with callsign
Control pointMust be in US for US stations
AutomaticNo control operator present

Auxiliary Operations

RepeatersAutomatically retransmit
BeaconsID regularly, propagation info
APRS digipeatersRelay position/data packets
Link stationsConnect repeaters together

🌐 NVIS β€” Near Vertical Incidence Skywave

Antenna pointed nearly straight up for regional coverage (100–300 mile radius) β€” eliminates skip zone.

Frequencies2–10 MHz typically
Antenna height< 0.1 wavelength above ground
Use caseState emergency nets, regional
NVIS is used by military and emergency management for reliable regional comms.

πŸ”­ Meteor Scatter & EME

Meteor scatterVHF off meteor ionization
DurationMilliseconds to seconds
EME (moonbounce)Via reflection off moon
EME path loss~250 dB each way
EME modesJT65, QRA64, CW